Schmelzindex-Tester
Plastic lab melt flow rate index meter tester
Melt flow rate instrument is also called plastic, Das Harzschmelzindexinstrument wird zur Messung der Schmelzflussrate verwendet, wenn der MFR-Wert des viskosen Fließzustands vorliegt, es gilt für das Polycarbonat, höhere Temperatur von aromatischem Sulfon, Fluor-Kunststoff, Nylon und andere technische Kunststoffe, can also be applied to polyethylene (PE), Polystyrol (PS), Polypropylen (Schmelzindexgerät xnr-400), ABS-Harz, polyformaldehyde (POM), Polycarbonat (PC) resin with lower melting temperature, wie Plastiktest, weit verbreitet in der Kunststoffproduktion, Kunststoff-Produkte, such as petroleum and chemical industry and related colleges and universities, Forschungseinrichtungen, and the commodity inspection department
Art:
1. The digital display
Set the electronic P.I.D regulator for temperature control, which is completely in line with national standards (cannot test melt volume flow rate and melt density).The machine also sets up the counter, which is convenient for measuring cutting time.The instrument works with the cutting and weighing method, and the scope is wide.
2. LCD is fully automatic.
Single chip microcomputer temperature control and program control, under test ended, and automatically display the time needed for a specific volume of the melt flows through the mouth mould, the calculation flow rate value, can repeat of high precision, easy to operate.The system is involved in temperature control.The manual cutting device can ensure the smooth detection by cutting and weighing method when automatic detection is not possible.Compact structure, beautiful shape, hohe Präzision, easy to use accessories.
3. Microcomputer controlled automatic.
The melt indexer sets up a single chip microcomputer automatic test device and electronic automatic cutting device.After the microcomputer system has input the corresponding parameters from the light touch key, the test is finished, namely, automatic calculation and printing of flow rate value, high repeatability and convenient operation.The temperature control of the use of computer software technology, which can automatically eliminate because of the power supply voltage fluctuation and the influence caused by environmental changes, and when the temperature of the instrument and the standard temperature thermometer (special correction to match) appeared deviation, the operator can easily random fixed.The electronic automatic cutting device can be automatically cut at the preselected interval to calculate the final result when automatic detection is not possible.
Hauptanwendung:
Melt flow rate instrument, used to measure the thermoplastic resin melt mass flow rate (MFR), Schmelzflussrate (MVR) Volumen und Dichte der Schmelze, es gilt nicht nur für die hohe Schmelztemperatur von Polycarbonat, Nylon, Fluor-Kunststoff, Technische Kunststoffe aus aromatischen Sulfonen, gilt auch für Polyethylen, Polystyrol, Polypropylen, ABS-Harz, Polyformaldehydharz mit niedrigerer Schmelztemperatur, wie Plastiktest, weit verbreitet in Kunststoffrohstoffen, Produkte, Erdöl- und Chemieindustrie, und verwandten Hochschulen und Universitäten, wissenschaftliche Forschungseinheiten und die Warenkontrollabteilung.
Barrel parameters |
Inner hole 9.55±0.025mm |
Pistons parameters |
Piston head: 9.475±0.015mm |
Piston length |
H=6.35±0.1mm |
Paramters |
Extrusion hole 1=2.095±0.005mm |
Temperature parameter |
With intelligent temperature control instrument,
with four pairs of significant temperature
setting control, PID-Parameter können automatisch eingestellt werden,
Genauigkeit bis zu ± 0.1 degree centigrade |
Temperaturbereich |
80degree centigrade~400degree centigrade |
Temperature accuracy |
±0.2 degree centigrade |
Bildschirmauflösung |
0.1degree centigrade |
Maximum comsuption |
< 600W |
Temperature accuracy |
4 mir. |
Weight parameters are as follows: |
Gewichtsgenauigkeit |
± 0,5% |
Basiseinstellung |
0.325kg ,1.2kg,2.16kg,3.8kg,5kg,10kg,12.5kg,21.6kg |
Position detection |
Control precision |
± 0.1mm |
Loop distance from up and down |
30Millimeter |
Test flow control |
|
Times of cutting the material |
0~10 times |
Material cutting interval |
0~999s(set reference Table 2) |
Control flow reaches the set temperature without volatility |
Barrel temperature time |
15 mir. |
Material be installed |
1 mir. |
Material sample temperature recovery time |
4 mir. |
When binder set |
1mir |
How it works:
Melt flow rate meter is in the specified temperature conditions, with high-temperature furnace to melt the state of the measured object. The molten state of the measured object, the required weight load by gravity out of a certain diameter hole in the test. Plastics in industrial enterprises and scientific research units of production, often with “melt (mass) flow rate” to represent the polymer material in the molten state of fluidity, viscosity and other physical properties. Melt flow rate refers to the extrudate, the average quality of the sample paragraphs are translated into 10 minutes of extrusion volume. Melt (mass) flow rate expressed by MFR, Einheit: G / 10 Protokoll (G / mir)
Formula: MFR (θ, mnom) = tref × m / t = 600 × m / t (g / 10 min)
Where: θ – Prüftemperatur
mnom – Nominal Load Kg
m – the average quality of cut g
tref – reference time (10mir): 600
t – cut off time interval unit: Sekunden.
Example:
A set of plastic samples, a cut every 30 Sekunden, the quality of the results section: 0.081 G, 0.086 G, 0.081 grams, 0.089 grams, 0.082 grams.
Cut the average quality m = (0.081 +0.086 +0.081 +0.089 +0.082) ÷ 5 = 0.0838 ≈ 0.084 (G)
Into the formula: MFR = 600 × 0.084/30 = 1.680 (G / 10 mir)
By Industry:
For factories and enterprises and research institutes in the production and research.
Den Kriterien entsprechend:
The machine design and manufacture in accordance with the requirements of GB/T3682-2000
technische Parameter:
Modell
Plastic Melt Flow Rate Tester, MFI Testing Machine
1. Squeeze out some material
Discharge port diameter Φ2.095±0.005mm
Discharge port length 8.000±0.025mm
Loaded barrel diameter Φ9.550±0.025mm
Loaded barrel length 152±0.1mm
Piston head diameter 9.475±0.015mm
Piston head length 6.350±0.100mm
2.Standard test load (acht Klassen)
1grade 0.325kg=(Stange + Gewicht + thermal units +1 Nein. tray body weight)
2Klasse 1.200 kg=(0.325+2 0.875 eight)
3Klasse 2.160 kg=(0.325+3 1.835 eight)
4Klasse 3.800 kg=(0.325+4 3.475 Gewicht)
5Klasse 5.000 kg=(0.325+5 4.675 Gewicht)
6Klasse 10.000 kg=(0.325+5 4.675 weight+6 5.000 Gewicht)
7Klasse 12.500 kg=(0.325+5 4.675 weight+6 5.000+7 2.500 Gewicht)
8Klasse 21.600 kg=(0.325+2 0.875+3 1.835+4